Service Area

Responded to no cooling complaint on Lennox XC14-030-230A10 outdoor condensing unit. Upon arrival, found unit completely inoperative with no power to compressor or condenser fan motor. Inspected electrical connections at unit and found failed contactor with burned contacts preventing 24V call for cooling from energizing compressor and fan circuits. Verified proper voltage at disconnect and confirmed 208/230V 1-phase power supply within acceptable range per manufacturer specifications. Replaced defective contactor, secured all wire connections, and verified proper amperage draw on compressor (within rated RLA) and condenser fan motor. Cycled unit multiple times to confirm reliable operation. System now cooling properly with all components functioning as designed.

Responded to no cooling call with reported loud noise prior to system failure. Upon arrival, found dual outdoor condenser unit system with one unit inoperative. Diagnosed failed compressor and contactor on affected unit. Replaced faulty compressor, installed new contactor, and recharged system to manufacturer specifications. Verified proper operation of smart thermostat control and confirmed cooling cycle functioning normally. System restored to full operational capacity with both condenser units running quietly and efficiently.

Completed spring preventative maintenance tune-up on Amana air conditioning system. Connected manifold gauges to verify refrigerant pressures and system operation, inspected condenser unit exterior condition, and documented equipment status with photos per PM protocol.

Completed preventative maintenance on residential outdoor AC condenser unit. Performed standard inspection of unit components, verified electrical connections and refrigerant lines, and documented equipment condition with photos. Unit operational at time of service.

Completed bi-annual preventative maintenance on residential HVAC system. Performed comprehensive inspection of air handler unit located in interior mechanical room, verified proper operation of all components, checked electrical connections, and inspected ductwork sealing. Proceeded to rooftop to service multiple condensing units, cleaned condenser coils, checked refrigerant levels, verified proper airflow across all units, and tested system operation under load to ensure optimal performance for continued reliable cooling.

Completed comprehensive A/C preventative maintenance on residential HVAC system located in utility closet. Performed full system inspection of air handler unit, verified proper airflow through ductwork, checked electrical connections and wiring, inspected condensate drain line for proper operation, and confirmed all safety labels and equipment were in compliance. All components operating within normal parameters with no issues identified during this scheduled maintenance visit.

Completed scheduled preventative maintenance on residential air conditioning system after 4PM per customer availability. Inspected and photographed capacitor assembly, noting dust accumulation and cobweb buildup on components and electrical connections. Performed standard PM checklist including system inspection and documentation of current operating condition.

Performed comprehensive assessment of existing electrical panel for replacement quote. Documented current panel configuration showing multiple circuit breakers with several red-handled breakers indicating potential Federal Pacific or similar older equipment requiring replacement. Photographed panel interior revealing circuit layout, existing labeling system with yellow notes, and overall condition of breaker arrangement. Also documented related electrical components including wall-mounted thermostat or control device to ensure compatibility considerations for new panel installation.

Completed preventive maintenance service on residential HVAC system. Performed thorough cleaning and inspection of outdoor AC condenser unit located on balcony, checked refrigerant lines and electrical connections. Inspected indoor equipment including furnace and Aprilaire humidifier system, verified proper operation of all components, cleared condensate drain lines, and confirmed system is operating within manufacturer specifications.

Conducted on-site assessment to provide estimate for malfunctioning exhaust vents and humidifier system. Inspected exterior PVC vent terminations protruding through deck skirting and evaluated crawl space conditions including ductwork, floor joists, and foundation areas to determine necessary repairs and equipment replacements for proper ventilation and humidity control.

Conducted site assessment for quote amendment to incorporate exterior electrical outlets. Documented existing conditions including exterior service area with accessible wall space near waste receptacle location and basement utility room showing current electrical panel and infrastructure. Photographed proposed installation areas to facilitate accurate pricing for additional exterior outlet installation work.

Conducted comprehensive electrical safety inspection of residential property focusing on code compliance and hazard mitigation. Evaluated existing wiring and conduit systems in utility room and exterior areas, identifying aged infrastructure with exposed components requiring attention. Successfully installed new conduit line connecting exterior wall penetration to garage, ensuring proper protection of electrical circuits and elimination of exposed wiring hazards throughout the premises.

Responded to service call for furnace producing loud noise during startup cycle. Upon inspection, accessed internal components of vertical air handler unit and examined blower assembly, motor mounts, and electrical connections. Photographed existing equipment configuration including copper refrigerant lines, blower motors, and cabinet assembly for documentation purposes. Provided estimate for necessary repairs to resolve startup noise issue.

Responded to service call for dual-unit HVAC system where one unit was reported as non-operational. Performed diagnostic inspection on commercial rooftop gas furnace unit, accessing internal components including burner assembly, gas lines, and electrical wiring. Documented equipment condition and configuration for customer with active membership account.

Performed estimate on commercial rooftop unit for new customer interested in club membership. Upon inspection, observed significant condensation on refrigerant lines with rust staining present, and noted corrosion on rooftop curb adapter frame requiring attention. Documented equipment condition with photos and provided recommendations for necessary repairs and preventive maintenance options.

Conducted comprehensive inspection of existing HVAC system in basement utility room, including York air conditioning unit and water heater installation. Prepared detailed estimate for replacement furnace and associated ductwork modifications to improve system efficiency and airflow distribution.

Responded to service call for power loss on second floor. Upon investigation, discovered disorganized electrical wiring with improper connections in junction box. Rewired connections according to code, secured loose wires, and installed proper wire nuts on all terminations, which restored power to all affected areas.

Completed installation of a 240V sub-meter in utility room. Mounted blue Sunray electrical enclosure securely to wall, connected all required conduits and verified proper voltage readings. Documented installation with photos for service records.

Conducted site assessment for potential electrical upgrades at the warehouse facility, documenting current lighting infrastructure including wall-mounted fluorescent fixtures and overall electrical layout. Customer requests similar electrical modifications as previously implemented at another location; comprehensive quote for recommended upgrades to be provided based on inspection findings.

Completed free system inspection promotion, examining electrical panel and rooftop HVAC units. Discovered significant wall damage exposing PVC plumbing, with signs of water damage requiring repair. Documented existing HVAC equipment on commercial rooftop and provided quote for new outlet installation as requested.

Performed complimentary A/C system evaluation as part of seasonal promotion. Inspected fan assembly and documented condition with detailed photographs. Unit appears to be functioning normally, though refrigerant levels may need monitoring for potential recharge in the future.

Conducted inspection of bathroom electrical fixtures to verify previous quote details. Documented existing ventilation fan, recessed lighting, and standard electrical outlet placement to ensure accurate assessment. Completed site evaluation for client to receive updated service proposal.

Performed diagnostic inspection on heating unit after tenant reported burnt smell. Examination of the furnace revealed exposed internal components including circuit board and wiring. Found water staining and deterioration around pipe installation area, which may be contributing to electrical issues causing the burnt odor. Recommended replacement of damaged components and sealing of water-compromised areas to prevent further damage.

Conducted on-site assessment for duct cleaning service requested in single classroom area. Inspection revealed extensive HVAC system with professionally installed galvanized steel ductwork, including insulated sections and associated condensate drainage. Additional examination of air handling equipment showed accessible internal components requiring maintenance attention, indicating potential for more comprehensive service than initially requested.

Performed diagnostic evaluation on two heating units exhibiting insufficient heat output. Inspection revealed internal component issues requiring attention, including potential problems with the control board circuitry and fan assembly as evidenced by multimeter testing. Recommend replacement of affected components to restore proper heating function and improve system efficiency.