Responded to no cooling complaint on Lennox XC14-030-230A10 outdoor condensing unit. Upon arrival, found unit completely inoperative with no power to compressor or condenser fan motor. Inspected electrical connections at unit and found failed contactor with burned contacts preventing 24V call for cooling from energizing compressor and fan circuits. Verified proper voltage at disconnect and confirmed 208/230V 1-phase power supply within acceptable range per manufacturer specifications. Replaced defective contactor, secured all wire connections, and verified proper amperage draw on compressor (within rated RLA) and condenser fan motor. Cycled unit multiple times to confirm reliable operation. System now cooling properly with all components functioning as designed.

Responded to no cooling call with reported loud noise prior to system failure. Upon arrival, found dual outdoor condenser unit system with one unit inoperative. Diagnosed failed compressor and contactor on affected unit. Replaced faulty compressor, installed new contactor, and recharged system to manufacturer specifications. Verified proper operation of smart thermostat control and confirmed cooling cycle functioning normally. System restored to full operational capacity with both condenser units running quietly and efficiently.

Completed bi-annual preventative maintenance on residential HVAC system. Performed comprehensive inspection of air handler unit located in interior mechanical room, verified proper operation of all components, checked electrical connections, and inspected ductwork sealing. Proceeded to rooftop to service multiple condensing units, cleaned condenser coils, checked refrigerant levels, verified proper airflow across all units, and tested system operation under load to ensure optimal performance for continued reliable cooling.

Completed comprehensive A/C preventative maintenance on residential HVAC system located in utility closet. Performed full system inspection of air handler unit, verified proper airflow through ductwork, checked electrical connections and wiring, inspected condensate drain line for proper operation, and confirmed all safety labels and equipment were in compliance. All components operating within normal parameters with no issues identified during this scheduled maintenance visit.

Completed preventive maintenance service on residential HVAC system. Performed thorough cleaning and inspection of outdoor AC condenser unit located on balcony, checked refrigerant lines and electrical connections. Inspected indoor equipment including furnace and Aprilaire humidifier system, verified proper operation of all components, cleared condensate drain lines, and confirmed system is operating within manufacturer specifications.

Conducted on-site assessment to provide estimate for malfunctioning exhaust vents and humidifier system. Inspected exterior PVC vent terminations protruding through deck skirting and evaluated crawl space conditions including ductwork, floor joists, and foundation areas to determine necessary repairs and equipment replacements for proper ventilation and humidity control.

Conducted comprehensive inspection of existing HVAC system in basement utility room, including York air conditioning unit and water heater installation. Prepared detailed estimate for replacement furnace and associated ductwork modifications to improve system efficiency and airflow distribution.

Performed complimentary A/C system evaluation as part of seasonal promotion. Inspected fan assembly and documented condition with detailed photographs. Unit appears to be functioning normally, though refrigerant levels may need monitoring for potential recharge in the future.

Conducted on-site assessment for duct cleaning service requested in single classroom area. Inspection revealed extensive HVAC system with professionally installed galvanized steel ductwork, including insulated sections and associated condensate drainage. Additional examination of air handling equipment showed accessible internal components requiring maintenance attention, indicating potential for more comprehensive service than initially requested.

Responded to service call for furnace with insufficient airflow. Upon inspection of the utility room, found a Rinnai tankless water heater with exposed components and various plumbing connections, but the primary HVAC issue was not visible in documentation. Recommended comprehensive ductwork inspection to identify airflow restrictions.

Conducted comprehensive assessment of existing furnace system in basement utility area. Documented current installation including gas/refrigerant lines, PVC ventilation pipes, and existing ductwork configuration. Prepared replacement estimate for complete furnace unit as requested by homeowner.

Conducted inspection of non-functioning bathroom powered humidifier as reported. Visual assessment revealed weathered metal components with possible connection issues at the cylindrical cap junction. Prepared estimate for replacement of suspected faulty motor assembly and associated mounting hardware to restore proper humidification function.

Conducted site assessment for requested tankless water heater installation with venting requirements. Existing Rheem tankless unit was observed with current copper piping connections. Evaluated electrical outlets and utility connections at installation location to determine compatibility with new system specifications.

Inspected south side downspout requiring heated cable installation, accessed through gangway as indicated in customer documentation. Evaluated malfunctioning sensor light mounted above gangway entrance. Documented existing conditions with photos showing the corridor approach and exterior access point for future installation planning.

Responded to customer report of possible pressure valve leak on 2023-installed furnace. Upon inspection of the residential hydronic heating system, examined copper piping network, manifolds with PEX connections, and zone control valves. No active leaks were found in the plumbing assembly or pressure relief valve. System pressure tested and verified to be operating within normal parameters.

Performed requested routine maintenance on client's older furnace, including thorough cleaning of burners. Conducted comprehensive inspection using borescope camera to examine internal components and verify proper cleaning of combustion chamber and heat exchanger surfaces.

Responded to service call for furnace failing to heat above 62 degrees. Diagnostic inspection revealed faulty limit switch preventing proper heating cycle completion. Replaced limit switch, cleaned flame sensor, and verified proper thermostat communication. System now operating correctly with heat output reaching desired temperature settings.

Performed initial assessment for customer's requested electrical upgrades. Inspected main circuit breaker panel and junction box with exposed wiring, noting aged components and disorganized wiring configuration. Documented existing electrical infrastructure with photos for comprehensive quote preparation.

Inducer motor replacement

Blower Wheel Wash, Furnace Deep Cleaning, Ductwork Camera Inspection to check for airway blockages.

Blower motor replacement, Furnace filter change, Blower wheel wash.

Preventative Maintenance for furnace

Preventative Maintenance on furnace

AC Disconnection/Reconnection for rooftop repair.

Estimate on replacing current system